The waste paper before packing is distributed in the innermost part of the packing station. Since the waste paper is usually all trucks or tricycles of stockholders when the waste paper is sent in, the car is exquisite and has strong maneuverability. It can be turned around and turned in the courtyard at will. It is helpful to put the scattered paper as centralized as possible and reduce Land occupation.
Once the baler is placed in the other corner of the baler, it is not easy to move again. Therefore, it is placed in the corner to reduce the area. The other is placed together with the waste paper before baling, which is conducive to grabbing the material in the car and lowering it. The scope of car-catching theme activities improves work efficiency.
If the above four points must be considered before the basic construction of the packing station, the work efficiency of most personnel should be increased by more than 20%, and the safety of the packing station can be reasonably ensured.
Nick Machinery has been engaged in the production and research of waste paper hydraulic balers for more than ten years and has rich maintenance experience. Welcome to contact 86-29-86031588, www.nkbaler.com.
2. The front and back drainage of the waste paper baler is serious. When working quickly, it is easy to cause the wind pressure to be too low, but it far overwhelms the oil return circuit. When the piston ring seal of the oil cylinder of the waste paper baler is worn, both sides of the cylinder of the waste paper baler It is easy to cause a problem with excessive air leakage, resulting in the rapid relocation of the cylinder of the waste paper baler, and the number of prefabricated components is also prone to oil leakage.
3. If the safety valve of the waste paper baler is deformed in the light pressure baler, it will seriously affect the main valve core. The main valve core is blocked at the small opening, which will cause the pressure oil of the door source baling pump to overflow into the oil tank and make the baling oil.
The packed waste paper is placed close to the entrance. The packed car is all 9.6 meters long. It has poor maneuverability and is difficult to turn around in the packing station. If the packed waste is piled up with accessories at the gate, the cart is only It must be turned into the hospital, and the car can be picked up immediately after it is installed.
The dormitory area is around the entrance and the personnel entering and exiting the packing station are now of mixed quality, so as to ensure the safety of the packing station. The dormitory area is placed here and can reasonably supervise the personnel entering and exiting.
Nick Machinery specializes in producing various waste paper balers, which are suitable for waste paper recycling stations of various specifications. The waste paper baler has advanced technology, reliable quality and stable performance. They are ideal for you.
Therefore, in the process of waste paper recycling, the waste paper should be handled in the following ways: remove the scraps before the waste paper; the waste paper baler can be deleted in the previous process, but can not be deleted in the next process; when the area of impurities is greater than and less than Area can be removed. It is best to eliminate it within a period of time.
Packaging waste paper and reusing Nick waste paper baler is the first choice. Now, the country calls for energy conservation, emission reduction and environmental protection. This policy can well promote our market share of waste paper baler. By improving the equipment structure, the best use effect can be ensured. For example, through experiments, adjusting the left and right position and force of the arm cylinder, the mineral water bottle packaging machine can make the waste paper packaging effect better; adjusting the bag weight is more convenient. The length and weight of the bundle can be freely controlled, and it is very convenient to load cars between different models. No overweight or loss of tons.
The future will greatly increase the recycling rate of waste paper and the effective utilization rate of waste paper. How to make money with waste paper baler? , Is also a development opportunity for the waste paper baler industry. In order to help users purchase high-quality fully automatic waste paper baler products, first check whether the process design of the fully automatic waste paper baler is reasonable. The better the process, the more reasonable the equipment composition, and the better the matching of components in the production process. The closer the distance, the better the production effect. At present, the country attaches great importance to environmental protection and resource reuse projects. Judging from the current recycling of waste paper products in my country, this is far from reaching the level of some developed countries.
But the price is much lower than the latter. This is a good choice to save capital investment. Hydraulic technology is different from market mechanical technology. Waste paper baler is currently the most convenient waste paper storage and transportation tool. The products play an important role in many waste paper recycling companies and paper companies.
Shaanxi Nick Machinery Equipment Co., Ltd. has been committed to the research, development and manufacturing of waste paper baler, hydraulic baler, plastic bottle baler, straw baler, and metal briquetting machine for many years, and has perfect after-sales service. We are willing to seek common development and create the future together with colleagues from all walks of life! Warmly welcome new and old friends at home and abroad to call, write, and visit our factory. WhatsAPP: 0086-15021631102 Website: http://www.nkbaler.com
4. Ten grades of extrusion force ranging from 63 tons to 400 tons for users to choose, production efficiency from 4 tons/shift to 40 tons/shift.
5. The size of the compression chamber and the size of the block can be customized according to customer requirements.
Causes of failure: the oil pump is emptied, the filter is blocked, the suction pipe or the pump inlet is blocked, the plunger is damaged, and the bearing is damaged
Solution: clean or replace the filter screen, clean the pipe; replace the new plug, bearing