Installation steps of hydraulic pipe of waste paper baler 2020-12-18

The waste paper baler produced by Nick Machinery is specially used for the recovery, compression and packaging of waste paper, waste cardboard, carton factory scraps, waste books, waste magazines, plastic film, straw and other loose materials.
Today, I will introduce to you the installation steps of the hydraulic pipeline of the waste paper baler:
1. Between parallel or intersecting pipe systems, there should be a gap of more than 10mm for the hydraulic oil of the waste paper baler.

2. The configuration of the pipeline must facilitate the installation and repair of pipelines, hydraulic valves and other components. Any section of the pipeline or components in the system should be freely disassembled and installed without affecting other components.

3. How to install the pipeline? When planning and piping, you should first consider the components, hydraulic components, and flanges to be connected based on the hydraulic schematic diagram.
4. The laying and direction of pipelines should be neat and common, with clear levels. Try to use horizontal or straight pipes. The non-parallelism of horizontal pipes should be ≤2/1000; the non-straightness of straight pipes should be ≤2/400, use a level gauge Detection.
5. When piping, it is necessary to make the pipeline have certain rigidity and anti-vibration ability.
6. The component of the pipeline should not be accepted by valves, pumps and other hydraulic components and accessories; nor should the pipeline support the heavier component component.
7. For longer pipelines, it is necessary to consider effective measures to avoid the stress caused by the expansion and contraction of the pipe due to temperature changes.
The series of waste paper balers produced by Nickel include: semi-automatic waste paper balers, automatic waste paper balers, horizontal waste paper balers, small vertical waste paper balers, etc., and can also be customized according to customers' intentions. , Nick’s product always has one suitable for you, you are welcome to inquire 86-29-86031588, www.nkbaler.com.

For Details

The classification and use method of the baler 2020-05-25

1. Manual baler
Use manual-operated split-type tools, manual tensioner (STTMR) and manual buckle (STTR). Applicable industries: round or irregular flat packaging such as steel pipes, steel coils, wires, cutting slits
Mode of operation: manual tensioner, used in conjunction with manual snap.
Features: Use manual operation, sturdy and durable, easy maintenance.

2. Fully automatic Baling machine
Automatic baling machine is suitable for: food, medicine, hardware, chemical, clothing, postal and other industries, suitable for carton packaging, paper packaging, parcel letter packaging, medicine box packaging, light industry packaging, hardware tools packaging, ceramic products packaging, auto parts packaging , Packaging of daily necessities, packaging of cultural and sports supplies, packaging of equipment, etc.
Features: Modular aluminum alloy bow design, easy to assemble and disassemble; fully automated design, more convenient operation and use; the maximum size of the bale is determined by the bow frame, the bow frame can be customized according to user needs; motor, reducer, cam 、 Tightening arm operation; excellent packing tightness, few failures, convenient maintenance; soft packing action, excellent durability, perfect packing function; the motor stops immediately after packing, saving power and practicality.

3. Metal baler
Applicable industries: steel, metal manufacturing, plywood, wood, electronics, logistics, etc.
Operation mode: Manually tighten and cut the belt at one time. Easy to maintain, easy to enter and only replace a few parts. Damaged parts can be replaced by customers. Ergonomic design, good balance of the machine body, bandwidth and cutter can be adjusted arbitrarily.

4. Packing and sealing machine
Applicable: Widely used in food, medicine, daily chemical, and other industries, suitable for packaging and packing of various sizes of goods such as carton packaging, paper packaging, medicine box packaging, light industry packaging, daily chemical supplies packaging, etc.
Features: With multiple protection devices, such as overload, phase loss, leakage, etc., to ensure the safe and normal use of equipment. The bundling machine adopts oil-free structure, which is easy to maintain and clean. The strapping machine adopts non-contact switch, the work is accurate and reliable, and the service life is long.

5. Semi-automatic Baling machine
Integrated circuit design: a new type of circuit design, which uses a plug-in circuit board to control the entire packing operation and the temperature of the scalding head. The circuit board replacement is very convenient. Instant heating, packing immediately: the first hot-melt design of the fast heating system, which can make the hot film work in 5 seconds and enter the best packing state. Automatic shutdown device, power saving and practical: When the packing operation is completed and no longer operates within 60 seconds, the motor will automatically stop and enter the standby state. New brake design: The brake of the machine's reel uses a special spring design to ensure that the belt enters smoothly and without noise.

6. Hydraulic baler
The hydraulic baler can squeeze various metal scraps (steel shavings, scrap steel, scrap aluminum, scrap copper, scrap stainless steel and scrap car scrap, etc.) into qualified furnace materials of various shapes such as cube, octagon, cylinder, etc. Transportation and smelting costs can increase the furnace speed.

7. Pneumatic baler
Pneumatic baler is a friction welding type baler. The overlapping thermoplastic straps are joined by the heat generated by the frictional movement, so it is called "friction welding". The compressed air presses down the piston of the cylinder. The upper part of the piston and the vibrator is connected with the positioning pin, and the vibrator presses the overlapping part of the packing belt. There is an oval hole in the middle of the vibrator, which is connected to the eccentric shaft of the air motor. The air motor rotates at high speed (10000 rpm), which makes the vibrator move back and forth quickly. The lower part of the packing belt is fixed by the triangular teeth of the bottom mold, and the upper part is driven by the triangular teeth of the vibrator, which is violently rubbed. In this way, the overlapping part of the packing tape is overheated and welded, and when the vibration timer reaches the set time, the welding is ended. The upper and lower parts of the strap are glued while squeezed and allowed to stand for a few seconds to ensure that the fusion joint has cooled.

For Details

Whats kind of Horizontal Type Baler you have 2020-05-09

Specialized in recycling and compressing the loose materials like plastic films ,PET bottles, plastic pallets ,waste paper ,grass ,fiber ,used clothes ,cartons ,cardboards trims ,scrap ,etc .

Full Horizontal Auto-tie Baler

Model	Bale size (mm)	Bale weight(kg)	Capacity	Motor
NKW40Q	700*700*1200	350-550	3-5 T/H	30HP
NKW60Q	850*750*1200	350-550	5-7T/H	40HP
NKW80Q	1000*800*1200	500-700	8-10T/H	60HP
NKW100Q	1000*1000*1400	800-1000	12-15T/H	80HP
NKW120Q	1100*1100*1200	1000-1200	15-18T/H	100HP
NKW160Q	1100*1100*1400	1100-1400	18-20T/H	120HP
NKW180Q	1100*1100*1600	1200-1500	20-25T/H	120HP
NKW200Q	1100*1100*1600	1200-1600	25-30T/H	150HP
NKW250Q	1100*1250*1600	1300-1700	30-35 T/H	180HP

for more information ,please visit us : www.nkbaler.com  or whatsapp us :+86 15021631102 

For Details

Used Rag wiper baler machine 2019-11-03

Rags wiper baler machine is a machine which is bale rags wiper for us. 
We alway called wiper baler, wiper baling press machine or rags packing machine, and somebody call it wiper rags bagging baler machine or many other names. Wiper rags, can be said to be in every corner of our life, every detail of life. From the kitchen to the bedroom to the guest room, it is also ubiquitous from the hotel, the family to the office. 
which line use this machine ?
this machine main for cleanning purpose ,Such universal necessities are not afraid of many, but they are rarely paid attention to. It is obvious that the main function of the cleaning cloth is to wipe the floor or table. Therefore, all the cotton, hemp and other fabrics used to wipe the objects can be called the rag.as more information ,please visit us :www.nkbaler.com

For Details

How do customers choose their own baler ? 2019-06-09

First of all, we should first select products according to the packaging effect and the size of the package. Besides, vertical balers and horizontal balers can finish packing. So what's the difference between vertical balers and horizontal balers? 

For Details

Cardboard Baler Operating Procedure 2018-11-08

Cardboard baler uses one or more metal plates and a hydraulic arm, 

pushing the plate down on cardboard with enormous pressure. 

Cardboard Bailer compacts the cardboard into a large, dense  rectangular or cube box which is typically held together by its own internal pressure. Then this bale is  tied with metal wire to secure it together and placed on a pallet which allows it to be moved through the use of a forklift or pallet jack.

For Details